Search

How GHS Affects OSHA’s Flammable Liquid Standard

Posted on 9/2/2014 by Joel Gregier

Flammable and combustible liquids have the potential to harm employees in the workplace, typically due to the fire hazard they pose. Because of this, the Occupational Safety and Health Administration (OSHA) maintains general requirements for the handling, storage, and use of liquids with a flash point below 200°F (“flammable liquids”) in containers, portable tanks, and tank systems. [29 CFR 1910.106]
 
The standard addresses the requirements for:
 
  • Design, construction, and capacity of flammable or combustible liquid storage units;
  • Ventilation; and
  • Storage.
GHS Modification
 
OSHA recently adopted the Globally Harmonized System for Classifying and Labeling of Chemicals (GHS). While the bulk of the adopted standards relate to OSHA’s Hazard Communication (HazCom) Standard, GHS also affects several other OSHA regulations, including the Flammable Liquid Standard.
 
The main modification to the Flammable Liquid Standard is how flammables are classified.
 
“Old” Flammable and Combustible Classification
 
Under OSHA’s “old” standard (pre-GHS), liquids were defined as either “flammable” or “combustible” and divided into three “classes.” 
 
Flammables were considered the more dangerous liquids under the pre-GHS standard. These liquids have lower flash points, meaning that they ignite more easily. Flammable liquids were defined as any liquid with a flash point below 100°F and were considered to be “Class 1 liquids.” A flammable could be Class 1A, 1B, or 1C, with 1A being the most dangerous.
 
OSHA defined combustibles as liquids with a flash point ranging from 100°F to 200°F. These liquids were divided into Class 2 and Class 3 liquids. Class 2 combustibles were more flammable than Class 3, due to their lower flash points.
 
The goal of OSHA’s pre-GHS standard was to ensure that the liquids that posed the greatest hazard were regulated more stringently than less hazardous liquids. 
 
“New” Flammable Classification
 
Now that OSHA has adopted the GHS, the Class 1, 2, and 3 distinctions no longer exist. “Flammable liquids” are now divided into four “categories.” Despite the change, OSHA’s goal remains the same: to reserve the most stringent regulations for the most dangerous liquids. In fact, many of the old classes have approximately the same cut-off levels for flash point and boiling point as the new categories.
 
Below are the four categories of flammable liquids (with their approximate “old class” as comparison):
 
  • Category 1 – liquids having flash points below 73.4°F (23°C) and a boiling point at or below 95°F (35°C) (~IA);
  • Category 2 – liquids having flash points below 73.4°F (23°C) and a boiling point above 95°F (35°C) (~IB);
  • Category 3 – liquids having flash points at or above 73.4°F (23°C) and at or below 140°F (60°C) (~IC and II); and
  • Category 4 – liquids having flash points above 140°F (60°C) and at or below 199.4°F (93°C) (~III). 
 
 [29 CFR 1910.106(a)(19)]
 
To find all of the requirements under OSHA’s Flammable Liquid Standard, see 29 CFR 1910.106.
 
OSHA Requires Employee HazCom Training 
 
Under OSHA’s Hazard Communication (HazCom) Standard, all employers must train employees on the hazards present in their workplace. The Hazard Communication Online Course has been updated to include important information about OSHA’s adoption of the Globally Harmonized System (GHS) into its HCS. Employees who complete the course will be prepared to recognize new GHS chemical labels, use revised classification criteria, and read 16-section Safety Data Sheets (SDSs).
 

Tags: GHS, HazCom, materials handling, osha

Find a Post

Compliance Archives

Lion - Quotes

The exercises in the DOT hazardous materials management course are especially helpful in evaluating your understanding of course information.

Morgan Bliss

Principal Industrial Hygienist

The instructor was energetic and made learning fun compared to dry instructors from other training providers.

Andy D’Amato

International Trade Compliance Manager

Course instructor was better prepared and presented better than other trainers. Course manual and references were easier to use as well.

Marty Brownfield

Hazardous Waste Professional

I can take what I learned in this workshop and apply it to everyday work and relate it to my activities.

Shane Hersh

Materials Handler

Attending Lion Technology classes should be mandatory for every facility that ships or stores hazmat.

Genell Drake

Outbound Lead

Lion courses always set the bar for content, reference, and practical application. Membership and access to the experts is an added bonus.

John Brown, CSP

Director of Safety & Env Affairs

Best instructor ever! I was going to take my DOT training w/a different provider, but based on this presentation, I will also be doing my DOT training w/Lion!

Donna Moot

Hazardous Waste Professional

The instructor was very patient and engaging - willing to answer and help explain subject matter.

Misty Filipp

Material Control Superintendent

Given the choice, I would do all coursework this way. In-person courses go very fast without the opportunity to pause or repeat anything.

Ellen Pelton

Chemical Laboratory Manager

As always, Lion never disappoints

Paul Resley

Environmental Coordinator

Download Our Latest Whitepaper

Knowing why TSDFs reject loads of hazardous waste—and the exact steps to follow if it happens—can reduce your anxiety and uncertainty about rejection.

Latest Whitepaper

By submitting your phone number, you agree to receive recurring marketing and training text messages. Consent to receive text messages is not required for any purchases. Text STOP at any time to cancel. Message and data rates may apply. View our Terms & Conditions and Privacy Policy.